1.1 Part A-General Test Methods for Evaluating the Basic Properties of Wood-Base Fiber and Particle Panel Materials These test methods cover the determination of the properties of wood-base fiber and particle panel materials that are produced as mat-formed panels such as particleboard, medium-density fiberboard and hardboard. Some of the test methods are applicable to other panel products such as oriented strand board. The test methods are as follows:

1.3 There are accepted basic test procedures for various fundamental properties of materials that may be used without modification for evaluating certain properties of wood-based fiber and particle panel materials. These test methods are included elsewhere in the Annual Book of ASTM Standards. The pertinent ones are listed in . A few of the test methods referenced are for construction where the wood-base materials often are used.

1.4 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents are approximate in many cases. 1 in. = 25.4 mm, 1 lbf = 4.45 N.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages	PDF Title
1	Scope
2	Referenced Documents Significance and Use Apparatus TABLE 1
3	Test Specimens Moisture Content and Conditioning Requirements Accelerated Aging
4	FIG. 1
5	Size, Physical Properties and Appearance of Panels FIG. 2 FIG. 3
6	Static Bending FIG. 4
7	FIG. 5
8	Tension Parallel to Surface FIG. 6 FIG. 7
9	Tension Perpendicular to Surface (Internal Bond) FIG. 8
10	Compression Parallel to Surface FIG. 9
11	Lateral Nail Resistance Test FIG. 10
12	Nail Withdrawal Test Nail-Head Pull-Through Test FIG. 11
13	FIG. 12 FIG. 13 FIG. 14
14	Direct Screw Withdrawal Test Hardness Test
15	Hardness Modulus Test FIG. 15
16	Shear in the Plane of the Panel FIG. 16
17	FIG. 17
18	Glue-Line Shear Test (Block Type) FIG. 18 FIG. 19
19	Falling Ball Impact Test FIG. 20 FIG. 21
20	Abrasion Resistance by the U.S. Navy Wear Tester FIG. 22 FIG. 23
21	Water Absorption and Thickness Swelling Linear Variation with Change in Moisture Content
22	Cupping and Twisting Interlaminar Shear FIG. 24
23	Edgewise Shear FIG. 25
24	FIG. 26 FIG. 27 FIG. 28
25	Compression-Shear Test Method FIG. 29 FIG. 30
26	FIG. 31
27	FIG. 32 TABLE 2
28	Test Panel Test Specimens Conditioning Thickness Modulus of Rupture FIG. 33
29	Tensile Strength Parallel to Surface FIG. 34
30	Tensile Strength Perpendicular to Surface Water Absorption and Thickness Swelling Moisture Content and Specific Gravity Report Precision and Bias Keywords

Published By	Publication Date	Number of Pages
ASTM	2006	30


PDF Format	Searchable	Printable	Preview Now

Standard Title	D1037-06 Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials
Published Code	ASTM
Publication Date	2006
Pages Count	30

ASTM-D1037:2006 Edition

PDF Catalog

Related products

ASTM-D1037:2006 Edition

ASTM-D1037:2012 Edition(Redline)

ASTM-D1037:1999 Edition

ASTM-D1037:1978 Edition

ASTM-D1037:2012 Edition

ASTM-D1037:2020 Edition