This European Standard specifies general technical delivery conditions for flat products for the construction of pressure equipment. The general technical delivery conditions in EN 10021 also apply. NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014\/68\/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014\/68\/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014\/68\/EU are satisfied, needs to be done.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | compares BS EN 10028-1:2017 <\/td>\n<\/tr>\n | ||||||
| 2<\/td>\n | TRACKED CHANGES Text example 1 \u2014 indicates added text (in green) <\/td>\n<\/tr>\n | ||||||
| 33<\/td>\n | National foreword <\/td>\n<\/tr>\n | ||||||
| 37<\/td>\n | 1 Scope 2 Normative references <\/td>\n<\/tr>\n | ||||||
| 39<\/td>\n | 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 40<\/td>\n | 4 Tolerances on dimensions 5 Calculation of mass 6 Classification and designation 6.1 Classification <\/td>\n<\/tr>\n | ||||||
| 41<\/td>\n | 6.2 Designation 7 Information to be supplied by the purchaser 7.1 Mandatory information <\/td>\n<\/tr>\n | ||||||
| 42<\/td>\n | 7.2 Options 7.3 Examples of ordering 8 Requirements 8.1 Steelmaking process 8.2 Delivery condition 8.3 Chemical composition <\/td>\n<\/tr>\n | ||||||
| 43<\/td>\n | 8.4 Mechanical properties 8.5 Surface condition 8.6 Internal soundness 9 Inspection 9.1 Types of inspection and inspection documents <\/td>\n<\/tr>\n | ||||||
| 44<\/td>\n | 9.2 Tests to be carried out <\/td>\n<\/tr>\n | ||||||
| 46<\/td>\n | 9.3 Retests, sorting and reprocessing 10 Sampling 10.1 Frequency of testing 10.2 Selection and preparation of samples and test pieces 10.2.1 Sampling and sample preparation 10.2.2 Preparation of test pieces 10.2.2.1 General <\/td>\n<\/tr>\n | ||||||
| 47<\/td>\n | 10.2.2.2 Test pieces for the tensile test 10.2.2.3 Test pieces for the impact test <\/td>\n<\/tr>\n | ||||||
| 51<\/td>\n | 11 Test methods 11.1 Chemical analysis 11.2 Tensile test at room temperature 11.3 Tensile test at elevated temperature 11.4 Impact test <\/td>\n<\/tr>\n | ||||||
| 52<\/td>\n | 11.5 Other testing 12 Marking <\/td>\n<\/tr>\n | ||||||
| 54<\/td>\n | Annex\u00a0A (informative)Changes to the previous version EN\u00a010028-1:2007+A1:2009 <\/td>\n<\/tr>\n | ||||||
| 55<\/td>\n | Annex\u00a0ZA (informative)Relationship between this European Standard and the Essential Requirements of EU\u00a0Directive 2014\/68\/EU aimed to be covered <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Tracked Changes. Flat products made of steels for pressure purposes – General requirements<\/b><\/p>\n |