{"id":225887,"date":"2024-10-19T14:40:44","date_gmt":"2024-10-19T14:40:44","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-60086-32011\/"},"modified":"2024-10-25T08:34:29","modified_gmt":"2024-10-25T08:34:29","slug":"bs-en-60086-32011","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-60086-32011\/","title":{"rendered":"BS EN 60086-3:2011"},"content":{"rendered":"
This part of IEC 60086 specifies dimensions, designation, methods of tests and requirements for primary batteries for watches. In several cases, a menu of test methods is given. When presenting battery electrical characteristics and\/or performance data, the manufacturer specifies which test method was used.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
6<\/td>\n | CONTENTS <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | INTRODUCTION <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
10<\/td>\n | 4 Physical requirements 4.1 Battery dimensions, symbols and size codes Figures \n Figure 1 \u2013 Dimensional drawing <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | Tables \n Table 1 \u2013 Dimensions and size codes <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 4.2 Terminals 4.3 Projection of the negative terminal (h5) 4.4 Shape of negative terminal Table 2 \u2013 Dimensions and size codes <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 4.5 Mechanical resistance to pressure 4.6 Deformation Figure 2 \u2013 Shape of negative terminal Table 3 \u2013 Minimum values of l1 Table 4 \u2013 Applied force F by battery dimensions <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 4.7 Leakage 4.8 Marking 5 Electrical requirements 5.1 Electrochemical system, nominal voltage, end-point voltage and open-circuit voltage <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 5.2 Closed circuit voltage Ucc (CCV), internal resistance and impedance 5.3 Capacity 5.4 Capacity retention 6 Sampling and quality assurance 6.1 General 6.2 Sampling Table 5 \u2013 Standardised electrochemical systems <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 6.3 Product quality indices 7 Test methods 7.1 Shape and dimensions 7.2 Electrical characteristics Figure 3 \u2013 Shape requirement <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | Figure 4 \u2013 Schematic voltage transient <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | Figure 5 \u2013 Curve: U = f(t) Figure 6 \u2013 Circuitry principle <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | Table 6 \u2013 Test method for Ucc (CCV) measurement <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | Figure 7 \u2013 Circuitry principle for method A Table 7 \u2013 Test method A for Ucc (CCV) measurement <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | Figure 8 \u2013 Circuitry principle for method B <\/td>\n<\/tr>\n | ||||||
22<\/td>\n | 7.3 Test methods for determining the resistance to leakage Table 8 \u2013 Discharge resistance (values) <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | Figure 9 \u2013 Test by temperature cycles Table 9 \u2013 Storage conditions for the recommended test Table 10 \u2013 Storage conditions for optional test <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | 8 Visual examination and acceptance conditions 8.1 Preconditioning 8.2 Magnification 8.3 Lighting 8.4 Leakage levels and classification <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | Table 11 \u2013 Leakage levels and classification <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | 8.5 Acceptance conditions <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | Annex A (normative) \nDesignation <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Primary batteries – Watch batteries<\/b><\/p>\n |