🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS IEC 60115-4-10:2023 – TC:2024 Edition

BS IEC 60115-4-10:2023 – TC:2024 Edition

$246.62

Tracked Changes. Fixed resistors for use in electronic equipment – Blank detail specification: Power resistors with axial leads for through-hole assembly on circuit boards (THT), for general electronic equipment, classification level G

Published By Publication Date Number of Pages
BSI 2024 110
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

PDF Catalog

PDF Pages PDF Title
1 30486603
60 A-30411008
61 undefined
63 CONTENTS
66 FOREWORD
68 0 Introduction to the template provided by this blank detail specification
0.1 Scope of this blank detail specification
0.2 Function of this blank detail specification
69 0.3 Identification of the detail specification and the resistor
71 1 Scope
2 Normative references
72 3 Terms and definitions
4 Characteristics and ratings
4.1 General
4.2 Dimensions
73 Figures
Figure 1 – Outline and dimensions
Tables
Table 1 – Styles and dimensions
74 4.3 Ratings
Figure 2 – Lead eccentricity of the wire terminations
Figure 3 – Length of excessive coating on the wire terminations
75 Table 2 – Climatic categories
Table 3 – Ratings
76 4.4 Resistance range and tolerance on resistance
Figure 4 – Derating curve for power resistors
77 5 Tests and test severities
5.1 General
5.2 Resistance
Table 4 – Temperature coefficients, tolerances and resistance rangesfor climatic category … / … / …
78 5.3 Temperature coefficient of resistance
5.4 Temperature rise
5.5 Endurance at the rated temperature 70 °C
5.6 Endurance at other than rated temperature
5.6.1 Endurance at room temperature
5.6.2 Endurance at a maximum temperature: UCT with category dissipation
5.7 Short-term overload of power resistors
5.7.1 Power film resistors
79 5.7.2 Wirewound resistors
5.8 Electrostatic discharge (ESD) test
5.9 Visual examination
Table 5 – Short-term overload duration
Table 6 – ESD test voltages
80 5.10 Gauging of dimensions
5.11 Detail dimensions
5.12 Robustness
5.12.1 Robustness of terminations
5.12.2 Robustness of the resistor body
5.13 Shock and vibration
5.13.1 Vibration
5.13.2 Shock or bump
5.14 Rapid change of temperature
81 5.15 Climatic sequence
5.16 Damp heat, steady state test
Table 7 – Additional cycles of the damp heat, cyclic test
Table 8 – Damp heat, steady state test duration
82 5.17 Solderability, with lead-free solder
5.18 Solderability, with SnPb solder
5.19 Resistance to soldering heat
5.20 Solvent resistance test
83 5.21 Insulation resistance
5.22 Voltage proof
5.23 Flammability test
6 Performance requirements
6.1 General
6.2 Limits for change of resistance at tests
84 6.3 Temperature coefficient of resistance
Table 9 – Limits for change of resistance at tests
85 6.4 Temperature rise
6.5 Visual examination
6.5.1 General visual criteria
Table 10 – Permitted change of resistance due to the variation of temperature
86 6.5.2 Visual criteria after tests
6.5.3 Visual criteria for packaging
6.6 Solderability
6.7 Insulation resistance
87 6.8 Flammability
7 Marking, packaging and ordering information
7.1 Marking of the component
7.2 Packaging
7.3 Marking of the packaging
7.4 Ordering information
88 8 Additional information
8.1 General
8.2 Storage and Transportation
8.3 Substrate for assembly
8.4 Soldering process
8.5 Use of cleaning agents or solvents
89 8.6 Coating or potting after assembly
9 Quality assessment procedures
9.1 General
9.1.1 100 % test
9.1.2 Certificate of Conformity (CoC)
90 9.1.3 Certified test records of released lots
9.2 Qualification approval
9.3 Maintenance of a qualification approval
9.3.1 Quality conformance inspection
9.3.2 Non-conforming specimen
91 Table 11 – Test schedule for the qualification approval of power resistors(1 of 5)
96 Table 12 – Test schedule for quality conformance inspection of power resistors(1 of 5)
102 Annex A (normative)Symbols and abbreviated terms
A.1 Symbols
104 A.2 Abbreviated terms
105 Annex B (normative)Reference for visual examination
106 Annex X (informative)Cross-reference for references to the prior revision of this specification
Table X.1 – Cross reference for references to clauses
107 Bibliography

Related products

BS IEC 60115-4-10:2023 - TC
$246.62