🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASTM-F2145:2009 Edition(Redline)

ASTM-F2145:2009 Edition(Redline)

$23.40

F2145-09 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing (Redline)

Published By Publication Date Number of Pages
ASTM 2009 5
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Abstract

This specification describes requirements and test methods for the qualification of Polyamide 11 (PA 11) bodied mechanical fittings for use with outside diameter controlled PA 11 pipe, and nominal 2 pipe size (IPS) and smaller. In addition, it specifies general requirements of the material from which these fittings are made. Performance requirements shall include tests to determine elevated temperature sustained pressure, tensile strength, in-line fitting, mechanical saddle fittings, temperature cycling, and joint constant tensile load.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification describes requirements and test methods for the qualification of Polyamide 11 (PA 11) and Polyamide 12 (PA12) bodied mechanical fittings for use with outside diameter controlled Polyamide 11 (PA 11) and Polyamide 12 (PA12) pipe, nominal 2 pipe size (IPS), and smaller complying with Specification D 2513. In addition, it specifies general requirements of the material from which these fittings are made.

1.2 The test methods described in this specification are not intended to be used as routine quality tests.

1.3 This specification covers the types of mechanical fittings covered in 3.2.1.

1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

1.6 The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D638 Test Method for Tensile Properties of Plastics D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure D1600 Terminology for Abbreviated Terms Relating to Plastics D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products F412 Terminology Relating to Plastic Piping Systems F1588 Test Method for Constant Tensile Load Joint Test (CTLJT)

ASME Standard

ASMEB31.8 Gas Transmission and Distribution Piping Systems Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.

Plastic Pipe Institute Standard

PPITR-4 PPI Listing of Hydrostatic Design Bases (HDB), Pressure Design Bases (PDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825, Irving, TX 75062, http://www.plasticpipe.org.

Keywords

gas; mechanical saddle fitting; plastic mechanical fitting; Polyamide 11 pipe; rotation test; temperature cycling test; Controlled diameters (outside); Mechanical fittings; Plastic pipe/tubing/fittings–specifications; Polyamide 11 (PA11); Rotation testing; Temperature cycling test;

ICS Code

ICS Number Code 23.040.45 (Plastic fittings)

DOI: 10.1520/F2145-09 ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]

Related products

ASTM-F2145
$23.40