Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASME A120.1 2021

ASME A120.1 2021

$98.04

ASME A120.1-2021 – Safety Requirements for Powered Platforms and Traveling Ladders and Gantries for Building Maintenance

Published By Publication Date Number of Pages
ASME 2021 49
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This Standard establishes safety requirements for powered platforms (scaffolds) for buildings where window cleaning and related services are accomplished by means of suspended equipment at heights in excess of 35 ft (11 m) above a safe surface (e.g., grade, street, floor, or roof level).

PDF Catalog

PDF Pages PDF Title
4 CONTENTS
5 FOREWORD
6 ASME A120 COMMITTEE ROSTER
7 CORRESPONDENCE WITH THE A120 COMMITTEE
9 ASME A120.1-2021 SUMMARY OF CHANGES
10 1 GENERAL RECOMMENDATIONS AND DEFINITIONS
1.1 Scope
1.2 Purpose
1.3 Application of This Standard
1.4 Applicable Units
11 1.5 Translation of Technical and Safety-Related Information
1.6 References
12 1.7 Terms and Definitions
15 2 BUILDING DESIGN REQUIREMENTS
2.1 General
2.2 Design Requirements
2.3 Specific Building Design Requirements
18 3 EQUIPMENT DESIGN AND CONSTRUCTION REQUIREMENTS
3.1 General
21 3.2 Specific Design Requirements
22 3.3 Carriage
Tables
Table 3.2.9-1 Minimum Clearance for Operation of Equipment Near High-Voltage Power Lines
23 3.4 Outriggers (Beam Type)
24 3.5 Davits and Rotatable Outriggers
25 Figures
Figure 3.5.1-1 Guide for Davit Raising Clearances
27 3.6 Hoisting Machines
28 3.7 Suspended Equipment
32 3.8 Remote Traversing Units
3.9 Supported Equipment
3.10 Suspension Wire Ropes and Rope Connections
34 3.11 Control, Power Circuits, and Components
36 4 TRAVELING LADDERS AND GANTRIES
4.1 General
4.2 Use and Application
4.3 Equipment Design
Table 4.3.2-1 Access
37 4.4 Safety Requirements
4.5 Fixed Ladders
4.6 Powered TLG
4.7 Hydraulic Equipment
5 INSPECTIONS, TESTS, OPERATION, AND MAINTENANCE
5.1 Inspections and Tests
39 5.2 Operation
5.3 Maintenance
41 MANDATORY APPENDIX I OPERATING MANUAL LAYOUT
I-1 TABLE OF CONTENTS
I-2 GENERAL DATA SUMMARY
I-3 DEFINITIONS
I-4 WARNINGS FOR OWNER AND USER
I-5 INTRODUCTION AND DESCRIPTION
I-6 CHECKS BEFORE RIGGING AND USE
I-7 RIGGING, SETUP, AND DERIGGING
I-8 CHECKS BEFORE OPERATION
I-9 OPERATION
I-10 TROUBLESHOOTING
42 I-11 EMERGENCY RECOVERY PROCEDURE/RESCUE
I-12 FINAL SAFETY DOs AND DON’Ts OR CHECKLIST
I-13 MAINTENANCE
I-14 WARRANTY
I-15 ELECTRICAL DIAGRAMS
I-16 ILLUSTRATION OF ALL LABELS AFFIXED TO EQUIPMENT
I-17 LIST OF REFERENCE MATERIAL/CODES
43 MANDATORY APPENDIX II MINIMUM REQUIREMENTS FOR PRE-USE/30-DAY MAINTENANCE INSPECTIONS
II-1 INTRODUCTION
II-2 GENERAL REQUIREMENTS FOR ALL EQUIPMENT
II-3 HOISTS
II-4 CARRIAGE
II-5 PLATFORMS
44 II-6 PERIODIC INSPECTIONS
45 NONMANDATORY APPENDIX A TYPICAL INTERMITTENT STABILIZATION SYSTEM
46 Figure A-1 Typical Intermittent Stabilization System

Related products

ASME A120.1 2021
$98.04