{"id":485983,"date":"2024-11-05T12:12:27","date_gmt":"2024-11-05T12:12:27","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/agma-1010-f14\/"},"modified":"2024-11-05T12:12:27","modified_gmt":"2024-11-05T12:12:27","slug":"agma-1010-f14","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/agma\/agma-1010-f14\/","title":{"rendered":"AGMA 1010-F14"},"content":{"rendered":"

\nSCOPE<\/strong><\/u><\/p>\n

\tThis standard provides nomenclature for general modes of gear tooth wear and failure. It classifies, identifies, and describes the most common types of failure and provides information that will, in many cases, enable the user to identify failure modes and evaluate the degree or change from original condition.<\/p>\n

\tThis standard is based on experience with steel gears; however, many of the failure modes discussed may apply to gears made from other materials.<\/p>\n

\tThe solution to many gear problems requires detailed investigation and analysis by specialists and is beyond the scope and intent of this standard.<\/p>\n

\tThis standard does not define \u201cgear failure\u201d. One observer's \u201cfailure\u201d is another observer's \u201crun-in\u201d. There is no single definition of gear failure, since whether or not a gear has failed depends on the specific application.<\/p>\n

\tThe methods given for reducing the risk of a failure mode are specific to the failure mode considered, and implementation may sometimes worsen, or create other failure modes or unintended consequences. Therefore, it is imperative that any remedy be evaluated prior to implementation and thoroughly tested and evaluated after implementation.<\/p>\n

\tNOTE: \u201cgear\u201d throughout the standard means gear or pinion unless the gear is specifically identified.<\/p>\n

\nFOREWORD<\/strong><\/u><\/p>\n

\t[The foreword, footnotes and annexes, if any, in this document are provided for informational purposes only and are not to be construed as a part of ANSI\/AGMA 1010-F14, Appearance of Gear Teeth – Terminology of Wear and Failure<\/em>.]<\/p>\n

\tThis standard provides a means to describe the appearance of gear teeth when they wear or fail. The study of gear tooth wear and failure has been hampered by the inability of two observers to describe the same phenomenon in terms that are adequate to assure uniform interpretation.<\/p>\n

\tThe term \u201cgear failure\u201d is subjective and a source of considerable disagreement.\u00a0 For example, a person observing gear teeth that have a bright, mirrorlike appearance may believe that the gears have \u201crun-in\u201d properly. However, another observer may believe that the gears have failed by polishing wear. Whether the gears should be considered failed or not depends on how much change from original condition is tolerable.<\/p>\n

\tThis standard provides a common language to describe gear wear and failure, and serves as a guide to uniformity and consistency in the use of that language.\u00a0 It describes the appearance of gear tooth failure modes and discusses their mechanisms, with the sole intent of facilitating identification of gear wear and failure.\u00a0 The purpose of the standard is to improve communication between equipment users and gear manufacturers for failure and wear analysis. Since there may be many different causes for each type of gear tooth wear or failure, it is not possible in the standard to identify a single cause for each type of wear or failure, nor to prescribe remedies.<\/p>\n

\tAGMA Standard 110 was first published in 1943. A revised standard, AGMA 110.03, was published in 1979 with improved photographs and additional material. AGMA 110.04 was reaffirmed by the members in 1989.<\/p>\n

\tANSI\/AGMA 1010-E95 was a revision of AGMA 110.04. It was approved by the AGMA Membership in March 9, 1995. It was approved as an American National Standard on December 13, 1995.<\/p>\n

\tANSI\/AGMA 1010-F14 is a revision of ANSI\/AGMA 1010-E95.\u00a0 It merges ANSI\/AGMA 1010-E95 and AGMA 912-A04.\u00a0 New failure modes and additional photos were added and the content was reorganized.\u00a0 The description of failure mode morphology and mechanism was expanded, and methods to reduce the risk of a particular failure mode were added to the description of many of the failure modes.<\/p>\n

\tThe first draft of ANSI\/AGMA 1010-F14 was made in August, 2010. It was approved by the AGMA membership in June, 2014.\u00a0 It was approved as an American National Standard on August 8, 2014.<\/p>\n","protected":false},"excerpt":{"rendered":"

Appearance of Gear Teeth – Terminology of Wear and Failure<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
AGMA<\/b><\/a><\/td>\n2014<\/td>\n89<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":485993,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[2659],"product_tag":[],"class_list":{"0":"post-485983","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-agma","8":"first","9":"instock","10":"sold-individually","11":"shipping-taxable","12":"purchasable","13":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/485983","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/485993"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=485983"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=485983"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=485983"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}