{"id":411505,"date":"2024-10-20T05:45:31","date_gmt":"2024-10-20T05:45:31","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-iso-263032022-tc\/"},"modified":"2024-10-26T10:39:29","modified_gmt":"2024-10-26T10:39:29","slug":"bs-iso-263032022-tc","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-iso-263032022-tc\/","title":{"rendered":"BS ISO 26303:2022 – TC"},"content":{"rendered":"
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
1<\/td>\n | 30464656 <\/td>\n<\/tr>\n | ||||||
101<\/td>\n | A-30421429 <\/td>\n<\/tr>\n | ||||||
102<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
106<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
107<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
109<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
112<\/td>\n | 4 Symbols 4.1 Uppercase letters <\/td>\n<\/tr>\n | ||||||
113<\/td>\n | 4.2 Lowercase letters 4.3 Greek letters <\/td>\n<\/tr>\n | ||||||
114<\/td>\n | 5 Preliminary remarks <\/td>\n<\/tr>\n | ||||||
115<\/td>\n | 6 Procedure for short-term capability evaluation 6.1 General Figure 1 \u2014 Basic procedure for short-term capability evaluation <\/td>\n<\/tr>\n | ||||||
116<\/td>\n | 6.2 Agreements <\/td>\n<\/tr>\n | ||||||
117<\/td>\n | Table 1 \u2014 Recommended values for short-term process capability parameters <\/td>\n<\/tr>\n | ||||||
118<\/td>\n | 6.3 Warm-up procedure 6.4 Adjustment <\/td>\n<\/tr>\n | ||||||
119<\/td>\n | 6.5 Production 6.6 Measurement <\/td>\n<\/tr>\n | ||||||
120<\/td>\n | 6.7 Computation and analysis 6.7.1 General <\/td>\n<\/tr>\n | ||||||
121<\/td>\n | Figure 2 \u2014 Evaluation diagram <\/td>\n<\/tr>\n | ||||||
122<\/td>\n | 6.7.2 Trend correction <\/td>\n<\/tr>\n | ||||||
123<\/td>\n | 6.7.3 Outlier management 6.7.4 Stability of the process <\/td>\n<\/tr>\n | ||||||
124<\/td>\n | 6.7.5 Calculation of indices 6.7.5.1 General <\/td>\n<\/tr>\n | ||||||
125<\/td>\n | 6.7.5.2 One-sided limited features 6.7.5.3 Surface roughness values 7 Factors influencing short-term capability evaluation 7.1 General <\/td>\n<\/tr>\n | ||||||
126<\/td>\n | Table 2 \u2014 Factors influencing short-term capability evaluation 7.2 Thermal influences <\/td>\n<\/tr>\n | ||||||
127<\/td>\n | 7.3 Influences due to measuring uncertainty 7.4 Influences arising from statistical analysis 7.4.1 Confidence level and sample size 7.4.2 Type of distribution <\/td>\n<\/tr>\n | ||||||
129<\/td>\n | Annex A (informative) Additional information related to statistical evaluations A.1 Relationship between centred and shifted distributions Figure A.1 \u2014 Short-term capability and shifted distribution <\/td>\n<\/tr>\n | ||||||
131<\/td>\n | A.2 Correlation between short-term range values, RV,s, and standard deviation <\/td>\n<\/tr>\n | ||||||
132<\/td>\n | Figure A.2 \u2014 Comparison of characteristic values for normal distribution <\/td>\n<\/tr>\n | ||||||
133<\/td>\n | A.3 Mean value not in the middle of the tolerance zone Figure A.3 \u2014 Effects if the mean value is not in the middle of the tolerance zone (offset of the mean value) A.4 Measurement uncertainty and short-term capability index <\/td>\n<\/tr>\n | ||||||
134<\/td>\n | Figure A.4 \u2014 Change of capability index by standard deviation of measuring device Figure A.5 \u2014 Standard deviation of measuring device and minimum tolerance <\/td>\n<\/tr>\n | ||||||
135<\/td>\n | A.5 Confidence level and sample size Figure A.6 \u2014 Confidence level and sample size, n, under the assumption of normal distribution of the characteristic values A.6 Type of distribution and capability index evaluation <\/td>\n<\/tr>\n | ||||||
136<\/td>\n | Figure A.7 \u2014 Influence of selected type of distribution <\/td>\n<\/tr>\n | ||||||
137<\/td>\n | Annex B (informative) Agreement forms <\/td>\n<\/tr>\n | ||||||
141<\/td>\n | Annex C (informative) Evaluation forms <\/td>\n<\/tr>\n | ||||||
145<\/td>\n | Annex D (informative) Examples of capability agreements and analysis <\/td>\n<\/tr>\n | ||||||
153<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Tracked Changes. Machine tools. Short-term capability evaluation of machining processes on metal-cutting machine tools<\/b><\/p>\n |