IEC 60384-13:2020 specifies preferred ratings and characteristics, selects from IEC 60384-1:2016 the appropriate quality assessment procedures, tests and measuring methods, and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level. Lower performance levels are not permitted. This part of IEC 60384 applies to fixed direct current capacitors, using as dielectric a polypropylene film with electrodes of thin metal foils. The capacitors covered by this document are intended for use in electronic equipment. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. This edition includes the following significant technical changes with respect to the previous edition: a) revision of all parts of the document based on the ISO\/IEC Directives, Part 2:2018, and harmonization with other similar kinds of documents; b) the document structure has been organized to follow new sectional specification structure decided in TC 40; c) revised tables and Clause 5 so as to prevent duplications and contradictions.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Annex ZA(normative)Normative references to international publicationswith their corresponding European publications <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 4 Preferred ratings and characteristics 4.1 Preferred climatic categories 4.1.1 General 4.1.2 Assisted drying 4.2 Preferred values of ratings 4.2.1 Nominal capacitance (CN) 4.2.2 Tolerance on nominal capacitance <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 4.2.3 Nominal capacitance with associated tolerance values 4.2.4 Rated voltage (UR) 4.2.5 Stability classes in relation to temperature coefficients and change of capacitance Tables Table 1 \u2013 Preferred combinations of capacitance series and tolerance <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 4.2.6 Category voltage (UC) 4.2.7 Rated temperature 5 Test and measurement procedures and performance requirements 5.1 Visual examination and check of dimensions 5.1.1 General 5.1.2 Examination methods 5.1.3 Requirements Table 2 \u2013 Preferred values and combinations <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 5.2 Electrical tests 5.2.1 Voltage proof 5.2.2 Capacitance Table 3 \u2013 Test voltages <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 5.2.3 Tangent of loss angle (tan \u03b4) 5.2.4 Insulation resistance <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 5.2.5 Characteristics depending on temperature (if required in the detail specification) Table 4 \u2013 Insulation resistance Table 5 \u2013 Correction factor dependent on test temperature <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 5.2.6 Inductance (if required) 5.2.7 Outer foil determination (if required) 5.3 Robustness of terminations 5.3.1 General 5.3.2 Initial inspections 5.3.3 Final inspections and requirements 5.4 Resistance to soldering heat 5.4.1 General 5.4.2 Preconditioning 5.4.3 Test conditions <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | 5.4.4 Final inspections and requirements 5.5 Solderability 5.5.1 General 5.5.2 Preconditioning 5.5.3 Test conditions 5.5.4 Final inspections and requirements 5.6 Rapid change of temperature 5.6.1 General 5.6.2 Initial inspections <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | 5.6.3 Test conditions 5.6.4 Final inspections and requirements 5.7 Vibration 5.7.1 General 5.7.2 Initial inspections 5.7.3 Mounting 5.7.4 Test conditions 5.7.5 Final inspections and requirements 5.8 Bump (repetitive shock) 5.8.1 General 5.8.2 Mounting <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | 5.8.3 Initial measurements 5.8.4 Test conditions 5.8.5 Final inspections and requirements 5.9 Shock 5.9.1 General 5.9.2 Mounting 5.9.3 Initial measurements 5.9.4 Test conditions Table 6 \u2013 Acceleration and duration of the pulse <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | 5.9.5 Final inspections and requirements 5.10 Climatic sequence 5.10.1 General 5.10.2 Initial measurements 5.10.3 Dry heat 5.10.4 Damp heat, cyclic, test Db, first cycle 5.10.5 Cold 5.10.6 Low air pressure (if required) 5.10.7 Damp heat, cyclic, Test Db, remaining cycles <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | 5.10.8 Recovery 5.10.9 Final inspections and requirements 5.11 Damp heat, steady state 5.11.1 General 5.11.2 Initial inspections 5.11.3 Test conditions 5.11.4 Recovery 5.11.5 Final inspections and requirements 5.12 Endurance 5.12.1 General 5.12.2 Initial inspections <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | 5.12.3 Test conditions 5.12.4 Final inspections and requirements 5.13 Component solvent resistance (if applicable) 5.14 Solvent resistance of the marking (if applicable) 6 Marking 6.1 General 6.2 Information for marking Table 7 \u2013 Endurance test <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 6.3 Marking on capacitors 6.4 Marking on packaging 6.5 Additional marking 7 Information to be given in the detail specification 7.1 General 7.2 Outline drawing and dimensions <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | 7.3 Mounting 7.4 Ratings and characteristics 7.4.1 General 7.4.2 Nominal capacitance range 7.4.3 Particular characteristics 7.4.4 Soldering 7.5 Marking 8 Quality assessment procedures 8.1 Primary stage of manufacture 8.2 Structurally similar components <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | 8.3 Certified records of released lots 8.4 Qualification approval 8.4.1 General 8.4.2 Qualification approval on the basis of the fixed sample size procedure <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | Table 8 \u2013 Fixed sample size test plan for qualification approval Assessment level EZ <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | Table 9 \u2013 Test schedule for qualification approval <\/td>\n<\/tr>\n | ||||||
| 34<\/td>\n | 8.5 Quality conformance inspection 8.5.1 Formation of inspection lots 8.5.2 Test schedule 8.5.3 Delayed delivery <\/td>\n<\/tr>\n | ||||||
| 35<\/td>\n | 8.5.4 Assessment levels Table 10 \u2013 Lot-by-lot inspection Table 11 \u2013 Periodic inspection <\/td>\n<\/tr>\n | ||||||
| 36<\/td>\n | Annex X (informative) Cross-references for references to the previous edition of this document Table X.1 \u2013 Cross-references <\/td>\n<\/tr>\n | ||||||
| 38<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Fixed capacitors for use in electronic equipment – Sectional specification. Fixed polypropylene film dielectric metal foil DC capacitors<\/b><\/p>\n |