{"id":249747,"date":"2024-10-19T16:28:00","date_gmt":"2024-10-19T16:28:00","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-60317-0-72012\/"},"modified":"2024-10-25T11:40:25","modified_gmt":"2024-10-25T11:40:25","slug":"bs-en-60317-0-72012","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-60317-0-72012\/","title":{"rendered":"BS EN 60317-0-7:2012"},"content":{"rendered":"
This part of IEC 60317 establishes general requirements for fully insulated (FIW) zero-defect enamelled round copper wires.<\/p>\n
The nominal conductor diameter range is given in the relevant technical specification.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
6<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | INTRODUCTION <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | 1 Scope 2 Normative references 3 Terms, definitions, general notes and appearance 3.1 Terms and definitions <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 3.2 General notes 3.2.1 Methods of test 3.2.2 Winding wire 3.3 Appearance 4 Dimensions 4.1 Conductor diameter <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 4.2 Out of roundness of conductor (for nominal diameters over 0,063\u00a0mm) 4.3 Minimum overall diameter 4.4 Maximum overall diameter <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | Tables Table 1 \u2013 Dimensions of enamelled wires (R\u00a020) (1 of 2) <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 5 Electrical resistance 6 Elongation Table 2 \u2013 Electrical resistance Table 3 \u2013 Elongation at break <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 7 Springiness 8 Flexibility and adherence 8.1 Mandrel winding test (for nominal conductor diameters up to and including 1,600\u00a0mm) Table 4 \u2013 Springiness <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 8.2 Jerk test (for nominal diameters up to and including 1,000 mm) 9 Heat shock Table 5 \u2013 Mandrel diameters for mandrel winding test <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | 10 Cut Through 11 Resistance to abrasion 12 Resistance to solvents Table 6 \u2013 Heat shock <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 13 Breakdown voltage 14 Continuity of insulation (nominal conductor diameters up to and including 1,600\u00a0mm) 14.1 Off-line high voltage continuity 14.2 In-line high voltage continuity 15 Temperature index 16 Resistance to refrigerants Table 7 \u2013 Breakdown voltage <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | 17 Solderability 18 Heat or solvent bonding 19 Dielectric dissipation factor 20 Resistance to transformer oil 21 Loss of mass 23 Pin-hole test 30 Packaging <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | Annex A (informative) Dimensions for intermediate nominal conductor diameter values (R 40) Table A.1 \u2013 Dimensions of enamelled wires without a bonding layer (R 40) <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Specifications for particular types of winding wires – General requirements. Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm<\/b><\/p>\n |