IEC 60384-13:2011 applies to fixed direct current capacitors, using as dielectric a polypropylene film with electrodes of thin metal foils. The capacitors covered by this standard are intended for use in electronic equipment. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. This fourth edition cancels and replaces the third edition published in 2006 and contains the following significant technical changes with respect to the previous edition. – Table 3, Sampling plan together with numbers of permissible non-conformance for qualification approval test, has been adjusted. – Table 5, Lot-by-lot inspection, has been changed, highlighting assessment level EZ only. – Table 6, Periodic inspection, has been changed, highlighting assessment level EZ only.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 6<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | 1 General 1.1 Scope 1.2 Object 1.3 Normative references <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 1.4 Information to be given in a detail specification <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 1.5 Terms and definitions 1.6 Marking <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 2 Preferred ratings and characteristics 2.1 Preferred characteristics 2.2 Preferred values of ratings Tables Table 1 \u2013 Preferred tolerances <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 3 Quality assessment procedures 3.1 Primary stage of manufacture Table 2 \u2013 Preferred values and combinations <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 3.2 Structurally similar components 3.3 Certified records of released lots 3.4 Qualification approval <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | Table 3 \u2013 Sampling plan together with numbers of permissible non-conformancefor qualification approval test <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | Table 4 \u2013 Test schedule for qualification approval <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 3.5 Quality conformance inspection <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Table 5 \u2013 Lot-by-lot inspection Table 6 \u2013 Periodic inspection <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | 4 Test and measurement procedures 4.1 Visual examination and check of dimensions 4.2 Electrical tests Table 7 \u2013 Test points and voltages <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | Table 8 \u2013 Insulation resistance requirements Table 9 \u2013 Correction factors <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | 4.3 Robustness of terminations 4.4 Resistance to soldering heat 4.5 Solderability <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | 4.6 Rapid change of temperature 4.7 Vibration 4.8 Bump <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 4.9 Shock 4.10 Climatic sequence Table 10 \u2013 Preferred severities <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | 4.11 Damp heat, steady state <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | 4.12 Endurance 4.13 Component solvent resistance 4.14 Solvent resistance of marking Table 11 \u2013 Test conditions <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Fixed capacitors for use in electronic equipment – Sectional specification\/ Fixed polypropylene film dielectric metal foil d.c. capacitors<\/b><\/p>\n |