ISO 8747:1997
$13.00
Clous cannelés à tête fraisée
| Published By | Publication Date | Number of Pages |
| ISO | 1997-11 | 8 |
La présente Norme internationale prescrit les caractéristiques des clous cannelés à tête fraisée, à trois cannelures constantes sur toute leur longueur, débouchantes d'un côté et régulièrement espacées, de diamètre nominal, d1, de 1,4 mm à 20 mm inclus. Le matériau refoulé de chaque côté des cannelures forme un renflement dont le diamètre d2, supérieur au diamètre nominal d1, permet un ajustement serré de ces clous cannelés lorsqu'ils sont emmanchés en force dans un trou de diamètre de perçage égal au diamètre nominal du clou d1 (voir article 4).
Related products
-
ISO 8947:1993
Matériel agricole — Matériel de travail du sol — Méthode d’essai des dents de cultivateurs…
-
ISO 5747:1995
Pinces et tenailles — Pinces articulées coupantes de côté, coupantes en bout et coupantes diagonale…
-
BS 2782-5 Method 540A:1977
Methods of testing plastics. Optical and colour properties, weathering – Determination of resistance to change…
-
BS EN ISO 8990:1996
Thermal insulation. Determination of steady-state thermal transmission properties. Calibrated and guarded hot box Published By…
-
ISO 8742:1997
Goupilles cannelées à cannelures centrales constantes sur le tiers de la longueur non débouchantes Published…
-
BS EN 28744:1992:1989 Edition
Grooved pins. Full length taper grooved Published By Publication Date Number of Pages BSI 1989…
-
ISO 877:1994
Plastics — Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to…
-
ISO 8777:1993
Information and documentation — Commands for interactive text searching Published By Publication Date Number of…
-
BS EN ISO 8741:1998
Grooved pins. Half-length reverse-taper grooved Published By Publication Date Number of Pages BSI 1998 14
-
ISO 8767:1992
Passenger car tyres — Methods of measuring rolling resistance Published By Publication Date Number of…
-
BS EN ISO 8744:1998
Grooved pins. Full-length taper grooved Published By Publication Date Number of Pages BSI 1998 14
-
ISO 8727:1997/Amd 1:2015
Mechanical vibration and shock — Human exposure — Biodynamic coordinate systems — Amendment 1 Published…
-
BS EN 28741:1992:1989 Edition
Grooved pins. Half length reverse taper grooved Published By Publication Date Number of Pages BSI…
-
BS 7163:1990
Specification for wire rope and pulley steering systems on small craft Published By Publication Date…
-
BS EN ISO 8746:1998
Grooved pins with round head Published By Publication Date Number of Pages BSI 1998 12
-
ISO 8743:1997
Grooved pins — Half-length centre grooved Published By Publication Date Number of Pages ISO 1997-11…
-
BS EN 28748:1992:1989 Edition
Spring-type straight pins. Coiled, heavy duty Published By Publication Date Number of Pages BSI 1989…
-
BS EN ISO 8745:1998
Grooved pins. Half-length taper grooved Published By Publication Date Number of Pages BSI 1998 14
-
BS EN ISO 801-1:1997:1995 Edition
Pulps. Determination of saleable mass in lots – Pulp baled in sheet form Published By…
-
BS EN ISO 8990:1996
Thermal insulation. Determination of steady-state thermal transmission properties. Calibrated and guarded hot box Published By…
-
ISO 8741:1997
Grooved pins — Half-length reverse-taper grooved Published By Publication Date Number of Pages ISO 1997-11…
-
ISO 8746:1997
Clous cannelés à tête ronde Published By Publication Date Number of Pages ISO 1997-11 8
-
ISO 7847:1987
Animal and vegetable fats and oils — Determination of polyunsaturated fatty acids with a cis,cis…
-
BS EN ISO 8742:1998
Grooved pins. One-third-length centre grooved Published By Publication Date Number of Pages BSI 1998 14
-
BS ISO 8727:1997+A1:2015
Mechanical vibration and shock. Human exposure. Biodynamic coordinate systems Published By Publication Date Number of…
-
BS EN ISO 8740:1998
Grooved pins. Full-length parallel grooved, with chamfer Published By Publication Date Number of Pages BSI…
-
ISO 8745:1997
Goupilles cannelées à cannelures progressives sur la moitié de la longueur (débouchantes) Published By Publication…
-
BS EN 28747:1992:1989 Edition
Grooved pins with countersunk head Published By Publication Date Number of Pages BSI 1989 13
-
ISO 8740:1997
Grooved pins — Full-length parallel grooved, with chamfer Published By Publication Date Number of Pages…
-
BS EN ISO 8748:1998
Spring-type straight pins. Coiled, heavy duty Published By Publication Date Number of Pages BSI 1998…
-
ISO/TR 8647:1990
Dégradation en environnement des textiles utilisés dans les équipements de retenue du fret aérien Published…
-
ISO 8727:1997
Mechanical vibration and shock — Human exposure — Biodynamic coordinate systems Published By Publication Date…
-
ISO 8147:1995
Construction navale et structures maritimes — Mâtures et leurs composants — Vocabulaire Published By Publication…
-
ISO 2747:1998
Émaux vitrifiés — Ustensiles de cuisson émaillés — Détermination de la résistance aux chocs thermiques…
-
BS EN 28740:1992:1989 Edition
Grooved pins. Full-length parallel grooved, with chamfer Published By Publication Date Number of Pages BSI…
-
BS EN ISO 8747:1998
Grooved pins with countersunk head Published By Publication Date Number of Pages BSI 1998 12
-
BS EN ISO 8743:1998
Grooved pins. Half-length centre grooved Published By Publication Date Number of Pages BSI 1998 14
-
BS EN 28743:1992:1989 Edition
Grooved pins. Half-length centre grooved Published By Publication Date Number of Pages BSI 1989 12
-
BS EN ISO 877:1997:1996 Edition
Plastics. Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to intensified…
-
ISO 8744:1997
Grooved pins — Full-length taper grooved Published By Publication Date Number of Pages ISO 1997-11…
