ISO 29782:2008
$13.00
Prostheses and orthoses — Factors to be considered when specifying a prosthesis for a person who has had a lower limb amputation
| Published By | Publication Date | Number of Pages |
| ISO | 2008-12 | 12 |
ISO 29782:2008 describes the factors to be considered when specifying a prosthesis for a person who has had a lower limb amputation.
Related products
-
ISO 29582-1:2009
Methods of testing cement — Determination of the heat of hydration — Part 1: Solution…
-
BS EN ISO 527-3:1996:2004 Edition
Plastics. Determination of tensile properties – Test conditions for films and sheets Published By Publication…
-
BS EN ISO 3521:2000:2004 Edition
Plastics. Unsaturated polyester and epoxy resins. Determination of overall volume shrinkage Published By Publication Date…
-
JIS R 5203:2015
Determination of the heat of hydration of cement – Solution method Published By Publication Date…
-
BS EN ISO 1628-3:2000
Plastics. Determination of the viscosity of polymers in dilute solution using capillary viscometers – Polyethylenes…
-
BS EN ISO 1133:2000
Plastics. Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of…
-
ISO/IEC TR 19782:2006
Information technology — Automatic identification and data capture techniques — Effects of gloss and low…
-
BS ISO 2782-2:2012
Rubber, vulcanized or thermoplastic. Determination of permeability to gases – Equal-pressure method Published By Publication…
-
ISO 29582-2:2009
Methods of testing cement — Determination of the heat of hydration — Part 2: Semi-adiabatic…
-
ISO 26782:2009
Matériel d’anesthésie et de réanimation respiratoire — Spiromètres destinés au mesurage des volumes expiratoires forcés…
-
BS EN ISO 11502:2005:2006 Edition
Plastics. Film and sheeting. Determination of blocking resistance Published By Publication Date Number of Pages…
-
BS EN ISO 183:2000
Plastics. Qualitative evaluation of the bleeding of colorants Published By Publication Date Number of Pages…
-
BS EN ISO 21003-3:2008+A1:2021:2022 Edition
Multilayer piping systems for hot and cold water installations inside buildings – Fittings Published By…
-
BS ISO 2782-2:2018 – TC:2020 Edition
Tracked Changes. Rubber, vulcanized or thermoplastic. Determination of permeability to gases – Equal-pressure method Published…
-
ISO 2782:2006
Rubber, vulcanized or thermoplastic — Determination of permeability to gases Published By Publication Date Number…
-
BS EN ISO 176:2000
Plastics. Determination of loss of plasticizers. Activated carbon method Published By Publication Date Number of…
-
ISO 2782-2:2018
Caoutchouc vulcanisé ou thermoplastique — Détermination de la perméabilité aux gaz — Partie 2: Méthode…
-
BS 2782-6:Methods 620A to 620D:1991:2003 Edition
Methods of testing plastics. Dimensional properties – Determination of density and relative density of non-cellular…
-
BSI PD ISO/IEC TR 19782:2006
Information technology. Automatic identification and data capture techniques. Effects of gloss and low substrate opacity…
-
BS EN ISO 1167-1:2006:2008 Edition
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids. Determination of the resistance to…
-
BS EN ISO 1167-2:2006:2008 Edition
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids. Determination of the resistance to…
-
BS EN ISO 1157:2000
Plastics. Cellulose acetate in dilute solution. Determination of viscosity number and viscosity ratio Published By…
-
BS EN ISO 175:2001
Plastics. Methods of test for the determination of the effects of immersion in liquid chemicals…
-
BS EN ISO 293:2003
Plastics. Compression moulding test specimens of thermoplastic materials Published By Publication Date Number of Pages…
-
BS EN ISO 7765-1:2004
Plastics film and sheeting. Determination of impact resistance by the free-falling dart method – Staircase…
-
BS ISO 3597-3:2003
Textile-glass-reinforced plastics. Determination of mechanical properties on rods made of roving-reinforced resin – Determination of…
-
BS 2782:1970:1987 Edition
Methods of testing plastics Published By Publication Date Number of Pages BSI 1987 46
-
BS ISO 1268-3:2000:2001 Edition
Fibre-reinforced plastics. Methods of producing test plates – Wet compression moulding Published By Publication Date…
-
ISO 29783-1:2008
Prosthetics and orthotics — Vocabulary — Part 1: Normal gait Published By Publication Date Number…
-
BS ISO 2782:2006 2007
Rubber, vulcanized or thermoplastic. Determination of permeability to gases Published By Publication Date Number of…
-
BS ISO 2982-2:2001
Rolling bearings. Accessories – Locknuts and locking devices. Dimensions Published By Publication Date Number of…
-
BS EN ISO 13846:2001
Plastics piping systems. End-load-bearing and non-end-load bearing assemblies and joints for thermoplastics pressure piping. Test…
-
BS EN ISO 294-2:1998:2006 Edition
Plastics. Injection moulding of test specimens of thermoplastic materials – Small tensile bars Published By…
-
BS EN ISO 2556:2001
Plastics. Determination of the gas transmission rate of films and thin sheets under atmospheric pressure.…
-
BS EN ISO 21003-3:2008+A1:2021:2024 Edition
Multilayer piping systems for hot and cold water installations inside buildings – Fittings Published By…
-
BS EN 740:1999:2001 Edition
Anaesthetic workstations and their modules. Particular requirements Published By Publication Date Number of Pages BSI…
-
ISO 29781:2008
Prostheses and orthoses — Factors to be included when describing physical activity of a person…
-
BS ISO 2782-2:2018
Rubber, vulcanized or thermoplastic. Determination of permeability to gases – Equal-pressure method Published By Publication…
-
BS 2782-7:Method 732B:1991
Methods of testing plastics. Rheological properties – Determination of viscosity number of poly(vinyl chloride) resins…
-
BS EN ISO 18453:2005:2006 Edition
Natural gas. Correlation between water content and water dew point Published By Publication Date Number…
