ISO 16630:2017
$19.50
Metallic materials — Sheet and strip — Hole expanding test
| Published By | Publication Date | Number of Pages |
| ISO | 2017-09 | 14 |
ISO 16630 describes a method of determining the hole expansion ratio in metallic sheets and strips with a thickness range of 1,2 mm to 6,0 mm inclusive and a width of at least 90 mm.
NOTE This test is normally applicable to sheet metal and is used to assess the suitability of the product for forming flanges.
Related products
-
ISO 15630-3:2019
Steel for the reinforcement and prestressing of concrete — Test methods — Part 3: Prestressing…
-
ISO 14630:2012
Non-active surgical implants — General requirements Published By Publication Date Number of Pages ISO 2012-12…
-
ISO 16620-5:2017
Plastics — Biobased content — Part 5: Declaration of biobased carbon content, biobased synthetic polymer…
-
ISO 16610-60:2015
Geometrical product specification (GPS) — Filtration — Part 60: Linear areal filters — Basic concepts…
-
ISO 16610-28:2016
Geometrical product specifications (GPS) — Filtration — Part 28: Profile filters: End effects Published By…
-
ISO 16730-1:2015
Fire safety engineering — Procedures and requirements for verification and validation of calculation methods —…
-
BS ISO 19630:2017
Fine ceramics (advanced ceramics, advanced technical ceramics). Methods of test for reinforcements. Determination of tensile…
-
ISO 16639:2017
Surveillance de l’activité volumique des substances radioactives dans l’air des lieux de travail des installations…
-
ISO 16610-1:2015
Geometrical product specifications (GPS) — Filtration — Part 1: Overview and basic concepts Published By…
-
ISO 1660:2017
Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing Published By Publication Date Number…
-
ISO 16638-2:2019
Radiological protection — Monitoring and internal dosimetry for specific materials — Part 2: Ingestion of…
-
ISO 16638-1:2015
Radiological protection — Monitoring and internal dosimetry for specific materials — Part 1: Inhalation of…
-
ISO 16610-41:2015
Spécification géométrique des produits (GPS) — Filtrage — Partie 41: Filtres de profil morphologiques: Filtre…
-
ISO 16635-2:2014
Dentistry — Dental rubber dam instruments — Part 2: Clamp forceps Published By Publication Date…
-
ISO 16634-2:2016
Produits alimentaires — Détermination de la teneur en azote total par combustion selon le principe…
-
ISO 16610-85:2013
Spécification géométrique des produits (GPS) — Filtrage — Partie 85: Filtres surfaciques morphologiques: Segmentation Published…
-
ISO 16632:2013
Tobacco and tobacco products — Determination of water content — Gas-chromatographic method Published By Publication…
-
ISO 16620-1:2015
Plastiques — Teneur biosourcée — Partie 1: Principes généraux Published By Publication Date Number of…
-
BS ISO 16620-5:2017
Plastics. Biobased content – Declaration of biobased carbon content, biobased synthetic polymer content and biobased…
-
ISO 16230-1:2015
Agricultural machinery and tractors — Safety of higher voltage electrical and electronic components and systems…
-
ISO 16631:2016
Ductile iron pipes, fittings, accessories and their joints compatible with plastic (PVC or PE) piping…
-
ISO 15630-1:2010
Steel for the reinforcement and prestressing of concrete — Test methods — Part 1: Reinforcing…
-
AS ISO 14630:2015
Non-active surgical implants – General requirements Published By Publication Date Number of Pages AS 2015-07-17…
-
ISO 1663:2007
Rigid cellular plastics — Determination of water vapour transmission properties Published By Publication Date Number…
-
ISO 16610-71:2014
Geometrical product specifications (GPS) — Filtration — Part 71: Robust areal filters: Gaussian regression filters…
-
ISO 16610-49:2015
Spécification géométrique des produits (GPS) — Filtrage — Partie 49: Filtres de profil morphologiques: Techniques…
-
ISO 16610-22:2015
Spécification géométrique des produits (GPS) — Filtrage — Partie 22: Filtres de profil linéaires: Filtres…
-
ISO 16610-61:2015
Geometrical product specification (GPS) — Filtration — Part 61: Linear areal filters — Gaussian filters…
-
ISO 16620-3:2015
Plastics — Biobased content — Part 3: Determination of biobased synthetic polymer content Published By…
-
ISO 16620-2:2015
Plastics — Biobased content — Part 2: Determination of biobased carbon content Published By Publication…
-
ISO 16610-29:2015
Geometrical product specifications (GPS) — Filtration — Part 29: Linear profile filters: Spline wavelets Published…
-
BS ISO 16632:2013
Tobacco and tobacco products. Determination of water content.Gas-chromatographic method Published By Publication Date Number of…
-
ISO 16620-4:2016
Plastiques — Teneur biosourcée — Partie 4: Détermination de la teneur en masse biosourcée Published…
-
ISO 19630:2017
Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods of test for reinforcements — Determination…
-
BS ISO 16630:2017
Metallic materials. Sheet and strip. Hole expanding test Published By Publication Date Number of Pages…
-
ISO 16610-40:2015
Geometrical product specifications (GPS) — Filtration — Part 40: Morphological profile filters: Basic concepts Published…
-
ISO 16530-1:2017
Petroleum and natural gas industries — Well integrity — Part 1: Life cycle governance Published…
-
ISO 16637:2016
Radiological protection — Monitoring and internal dosimetry for staff members exposed to medical radionuclides as…
-
ISO 16610-30:2015
Geometrical product specifications (GPS) — Filtration — Part 30: Robust profile filters: Basic concepts Published…
-
ISO 16130:2015
Aerospace series — Dynamic testing of the locking behaviour of bolted connections under transverse loading…
