BS ISO 199:2014
$167.15
Rolling bearings. Thrust bearings. Geometrical product specification (GPS) and tolerance values
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 44 |
This International Standard specifies dimensional characteristics, limit deviations from nominal values, and tolerance values to define the interface (except chamfers) of thrust rolling bearings. Nominal boundary dimensions are defined in ISO 104[1].
This International Standard is not applicable to certain thrust bearings (e.g. thrust needle roller bearings) or for particular fields of application (e.g. special thrust precision bearings). Tolerances for such bearings are given in the relevant International Standards.
Chamfer dimension limits are given in ISO 582[3].
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Introduction |
| 9 | Section sec_1 Section sec_2 Section sec_3 Section sec_4 1 Scope 2 Normative references 3 Terms and definitions 4 Symbols |
| 10 | Table tab_1 |
| 11 | Table tab_1___1 |
| 12 | Table tab_a Figure fig_1 Table tab_b Figure fig_2 |
| 13 | Table tab_c Figure fig_3 |
| 14 | Table tab_d Figure fig_4 |
| 15 | Section sec_5 Section sec_5.1 5 Limit deviations and tolerance values 5.1 General |
| 16 | Section sec_5.2 Table tab_2 5.2 Tolerance class Normal |
| 17 | Table tab_3 |
| 18 | Section sec_5.3 Table tab_4 5.3 Tolerance class 6 |
| 19 | Table tab_5 |
| 20 | Section sec_5.4 Table tab_6 5.4 Tolerance class 5 |
| 21 | Table tab_7 |
| 22 | Section sec_5.5 Table tab_8 5.5 Tolerance class 4 |
| 23 | Table tab_9 |
| 24 | Annex sec_A Table tab_A.1 Annex A (informative) Symbols and terms as given in ISO 199:2005 in relationship to new descriptions given in this document |
| 25 | Table tab_A.1___1 |
| 26 | Annex sec_B Figure fig_B.1 Annex B (informative) Example of drawing indications of characteristics with specification for thrust bearings |
| 27 | Figure fig_B.2 |
| 28 | Annex sec_C Annex sec_C.1 Annex sec_C.2 Annex sec_C.2.1 Annex C (informative) Illustration of ISO 1132-1[4] and ISO 14405-1 terms and definitions |
| 29 | Annex sec_C.2.2 Annex sec_C.2.2.1 Annex sec_C.2.2.2 |
| 30 | Table tab_e Figure fig_C.1 |
| 31 | Table tab_f Figure fig_C.2 |
| 32 | Table tab_g Figure fig_C.3 |
| 33 | Annex sec_D Annex sec_D.1 Annex sec_D.2 Table tab_D.1 Annex D (informative) Description with illustrations for specification modifiers of linear sizes |
| 34 | Table tab_D.2 Annex sec_D.3 |
| 36 | Table tab_h Figure fig_D.1 |
| 37 | Table tab_i Figure fig_D.2 |
| 38 | Table tab_j Figure fig_D.3 |
| 39 | Figure fig_D.4 Annex sec_D.4 Annex sec_D.4.1 Table tab_k Figure fig_D.5 |
| 40 | Annex sec_D.5 Annex sec_D.5.1 Annex sec_D.5.2 Table tab_l Figure fig_D.6 |
| 41 | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Reference ref_5 Reference ref_6 Reference ref_7 Reference ref_8 Reference ref_9 Reference ref_10 Reference ref_11 Reference ref_12 Reference ref_13 Bibliography |
Related products
-
BS EN ISO 7199:2014
Cardiovascular implants and artificial organs. Blood-gas exchangers (oxygenators) Published By Publication Date Number of Pages…
