🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN IEC 60384-13:2020

BS EN IEC 60384-13:2020

$167.15

Fixed capacitors for use in electronic equipment – Sectional specification. Fixed polypropylene film dielectric metal foil DC capacitors

Published By Publication Date Number of Pages
BSI 2020 40
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

IEC 60384-13:2020 specifies preferred ratings and characteristics, selects from IEC 60384-1:2016 the appropriate quality assessment procedures, tests and measuring methods, and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level. Lower performance levels are not permitted. This part of IEC 60384 applies to fixed direct current capacitors, using as dielectric a polypropylene film with electrodes of thin metal foils. The capacitors covered by this document are intended for use in electronic equipment. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. This edition includes the following significant technical changes with respect to the previous edition: a) revision of all parts of the document based on the ISO/IEC Directives, Part 2:2018, and harmonization with other similar kinds of documents; b) the document structure has been organized to follow new sectional specification structure decided in TC 40; c) revised tables and Clause 5 so as to prevent duplications and contradictions.

PDF Catalog

PDF Pages PDF Title
2 undefined
5 Annex ZA(normative)Normative references to international publicationswith their corresponding European publications
7 English
CONTENTS
10 FOREWORD
12 1 Scope
2 Normative references
3 Terms and definitions
13 4 Preferred ratings and characteristics
4.1 Preferred climatic categories
4.1.1 General
4.1.2 Assisted drying
4.2 Preferred values of ratings
4.2.1 Nominal capacitance (CN)
4.2.2 Tolerance on nominal capacitance
14 4.2.3 Nominal capacitance with associated tolerance values
4.2.4 Rated voltage (UR)
4.2.5 Stability classes in relation to temperature coefficients and change of capacitance
Tables
Table 1 – Preferred combinations of capacitance series and tolerance
15 4.2.6 Category voltage (UC)
4.2.7 Rated temperature
5 Test and measurement procedures and performance requirements
5.1 Visual examination and check of dimensions
5.1.1 General
5.1.2 Examination methods
5.1.3 Requirements
Table 2 – Preferred values and combinations
16 5.2 Electrical tests
5.2.1 Voltage proof
5.2.2 Capacitance
Table 3 – Test voltages
17 5.2.3 Tangent of loss angle (tan δ)
5.2.4 Insulation resistance
18 5.2.5 Characteristics depending on temperature (if required in the detail specification)
Table 4 – Insulation resistance
Table 5 – Correction factor dependent on test temperature
19 5.2.6 Inductance (if required)
5.2.7 Outer foil determination (if required)
5.3 Robustness of terminations
5.3.1 General
5.3.2 Initial inspections
5.3.3 Final inspections and requirements
5.4 Resistance to soldering heat
5.4.1 General
5.4.2 Preconditioning
5.4.3 Test conditions
20 5.4.4 Final inspections and requirements
5.5 Solderability
5.5.1 General
5.5.2 Preconditioning
5.5.3 Test conditions
5.5.4 Final inspections and requirements
5.6 Rapid change of temperature
5.6.1 General
5.6.2 Initial inspections
21 5.6.3 Test conditions
5.6.4 Final inspections and requirements
5.7 Vibration
5.7.1 General
5.7.2 Initial inspections
5.7.3 Mounting
5.7.4 Test conditions
5.7.5 Final inspections and requirements
5.8 Bump (repetitive shock)
5.8.1 General
5.8.2 Mounting
22 5.8.3 Initial measurements
5.8.4 Test conditions
5.8.5 Final inspections and requirements
5.9 Shock
5.9.1 General
5.9.2 Mounting
5.9.3 Initial measurements
5.9.4 Test conditions
Table 6 – Acceleration and duration of the pulse
23 5.9.5 Final inspections and requirements
5.10 Climatic sequence
5.10.1 General
5.10.2 Initial measurements
5.10.3 Dry heat
5.10.4 Damp heat, cyclic, test Db, first cycle
5.10.5 Cold
5.10.6 Low air pressure (if required)
5.10.7 Damp heat, cyclic, Test Db, remaining cycles
24 5.10.8 Recovery
5.10.9 Final inspections and requirements
5.11 Damp heat, steady state
5.11.1 General
5.11.2 Initial inspections
5.11.3 Test conditions
5.11.4 Recovery
5.11.5 Final inspections and requirements
5.12 Endurance
5.12.1 General
5.12.2 Initial inspections
25 5.12.3 Test conditions
5.12.4 Final inspections and requirements
5.13 Component solvent resistance (if applicable)
5.14 Solvent resistance of the marking (if applicable)
6 Marking
6.1 General
6.2 Information for marking
Table 7 – Endurance test
26 6.3 Marking on capacitors
6.4 Marking on packaging
6.5 Additional marking
7 Information to be given in the detail specification
7.1 General
7.2 Outline drawing and dimensions
27 7.3 Mounting
7.4 Ratings and characteristics
7.4.1 General
7.4.2 Nominal capacitance range
7.4.3 Particular characteristics
7.4.4 Soldering
7.5 Marking
8 Quality assessment procedures
8.1 Primary stage of manufacture
8.2 Structurally similar components
28 8.3 Certified records of released lots
8.4 Qualification approval
8.4.1 General
8.4.2 Qualification approval on the basis of the fixed sample size procedure
29 Table 8 – Fixed sample size test plan for qualification approval Assessment level EZ
30 Table 9 – Test schedule for qualification approval
34 8.5 Quality conformance inspection
8.5.1 Formation of inspection lots
8.5.2 Test schedule
8.5.3 Delayed delivery
35 8.5.4 Assessment levels
Table 10 – Lot-by-lot inspection
Table 11 – Periodic inspection
36 Annex X (informative) Cross-references for references to the previous edition of this document
Table X.1 – Cross-references
38 Bibliography

Related products

BS EN IEC 60384-13:2020
$167.15