BS EN 4500-002:2024
$142.49
Aerospace series. Metallic materials. Rules for drafting and presentation of material standards – Specific rules for aluminium, aluminium alloys and magnesium alloys
| Published By | Publication Date | Number of Pages |
| BSI | 2024 | 32 |
The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications. This Part 002 specifies the “Specific rules for aluminium, aluminium alloys and magnesium alloys”.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 8 | 1 Scope 2 Normative references 3 Terms and definitions 4 Rules for drafting a European standard for aerospace metallic materials 4.1 General 4.2 Title 4.2.1 General |
| 9 | 4.2.2 Condition T4 and T42 or T6 and T62 4.2.3 Descriptions 4.2.3.1 General 4.2.3.2 Surface condition entries 4.2.3.3 Form entries |
| 10 | 4.2.3.4 Additional information entries |
| 11 | 4.3 Introduction 4.3.1 General 4.3.2 Condition Tx510 and Tx511, applicable to extruded bars and sections and drawn tubes 4.4 Scope, normative references, terms and definitions, requirements 4.5 Table 1 (1 of 3) 4.5.1 Line 1: Material designation 4.5.2 Line 2: Chemical composition 4.5.3 Line 3: Method of melting 4.5.4 Line 4.1: Form |
| 12 | 4.5.5 Line 4.2: Method of production 4.5.6 Line 4.3: Limit dimension(s) 4.5.7 Line 5: Technical specification 4.5.8 Line 6.1: Delivery condition and Heat treatment 4.5.9 Line 6.2: Delivery condition code 4.5.10 Line 7: Use condition and Heat treatment 4.5.11 Line 8.1: Test sample(s) 4.5.12 Line 8.2: Test piece(s) 4.5.13 Line 8.3: Heat treatment 4.5.14 Line 9: Dimensions concerned 4.5.15 Line 10: Thickness of cladding on each face 4.5.16 Line 11: Direction of test piece |
| 13 | 4.5.17 Lines 12 to 16: Tensile (T) 4.5.18 Line 17: Hardness 4.5.19 Line 18: Shear strength 4.5.20 Line 19: Bending 4.5.21 Line 20: Impact strength 4.5.22 Lines 21 to 26: Creep (C) 4.5.23 Line 27: Notes (see line 98) 4.6 Table 1 (2 of 3) 4.6.1 Lines 28 to 94 |
| 14 | 4.6.2 Line 95: Marking inspection 4.6.3 Line 96: Dimensional inspection 4.6.4 Line 98: Notes 4.6.5 Line 99: Typical use 4.7 Table 1 (3 of 3) 4.8 Bibliography |
| 15 | Annex A (informative)Completion of title page |
| 16 | Annex B (informative)Completion of the introduction |
| 17 | Annex C (informative)Completion of the scope, normative references, terms and definitions, and requirements |
| 18 | Annex D (informative)Completion of Table 1 (1 of 3) |
| 19 | Annex E (informative)Completion of Table 1 (2 of 3) |
| 24 | Annex F (informative)Completion of Table 1 (3 of 3) |
| 28 | Annex G (informative)Completion of the bibliography |
