BS EN 4106:2013

$102.76

Aerospace series. Non-metallic materials. Structural adhesive systems. Paste adhesive. Technical specification

Published By	Publication Date	Number of Pages
BSI	2013	22

Guaranteed Safe Checkout

Categories: 49.025.50 - Adhesives, BSI

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This European Standard defines the requirements for manufacture, qualification, inspection and testing of products in structural adhesive systems where the adhesive is supplied in the form of a paste, either a one part or two part system, for aerospace applications. The adhesive may be used in conjunction with a primer whose requirements are also included in this European Standard. It is applicable whenever referenced on a material standard.

PDF Catalog

PDF Pages	PDF Title
7	1 Scope 2 Normative references
8	3 Terms, definitions, symbols and abbreviations
9	4 Requirements 4.1 General requirements 4.1.1 Manufacturing schedule for paste adhesive 4.1.2 Traceability
10	4.1.3 Freedom from defects 4.1.4 Health and safety The safety data sheet shall be available and shall be provided prior to qualification testing. 4.1.5 Dimensions 4.2 Technical requirements 4.2.1 General 4.2.2 Required testing
11	4.2.3 Test samples Samples taken from fully finished products (condition of use) shall not be further processed. 4.2.4 Shelf life Shelf life shall start from the date of manufacture. 4.2.5 Shoplife 4.2.6 Requirements specific to paste adhesive systems 4.2.6.1 Colour 4.2.6.2 Composition 4.2.6.3 Curing
12	5 Qualification 5.1 Introduction 5.2 Approval of quality system 5.3 Product qualification 5.4 Test requirements 5.4.1 Material Qualification For new products or new manufacturers the full qualification testing shall be required (see Table 3 to Table 7). 5.4.2 Reduced qualification 5.4.3 Re-qualification 5.5 Qualification re-tests
13	5.6 Qualification test report 5.7 Interpretation of test results 6 Release testing 6.1 General 6.2 Sampling 6.2.1 Primer
14	6.2.2 Adhesive 6.3 Required tests The tests required for batch release are listed in Table 3 to Table 7. 6.4 Conformance 6.4.1 General 6.4.2 Rejection
15	6.4.3 Re-tests If all re-test results conform the batch shall be accepted. If one or more re-tests do not conform the batch shall be rejected. 6.5 Special tests 6.6 Capability clause 6.7 Release test report
16	7 Preparation for delivery 7.1 Packaging The primer shall be filled into airtight containers. The adhesive shall be filled into airtight containers. 7.2 Marking 7.2.1 Product containers This requirement applies equally to all components of the adhesive system. 7.2.2 Packages
17	7.3 Shipping conditions 7.4 Storage prior to shipping 8 Declaration of conformity

Additional information

Status	Definitive
Pages	22
Publication Date	2013-01-31
ISBN	978 0 580 80247 8
Standard Number	BS EN 4106:2013
Title	Aerospace series. Non-metallic materials. Structural adhesive systems. Paste adhesive. Technical specification
Identical National Standard Of	EN 4106:2013
Descriptors	Adhesion tests, Aircraft components, Mathematical calculations, Environmental testing, Air transport engineering, Testing conditions, Designations, Adhesives, Adhesive-bonded joints
Publisher	BSI
Committee	ACE/65
ICS Codes	49.025.50 - Adhesives

Preview PDF


PDF Format	Searchable	Printable	Preview Now

BS EN 4106:2013

PDF Catalog

Related products