šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
ASTM-E18:2011 Edition(Redline)

ASTM-E18:2011 Edition(Redline)

$38.35

E18-11 Standard Test Methods for Rockwell Hardness of Metallic Materials (Redline)

Published By Publication Date Number of Pages
ASTM 2011 37
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

Significance and Use

The Rockwell hardness test is an empirical indentation hardness test that can provide useful information about metallic materials. This information may correlate to tensile strength, wear resistance, ductility, and other physical characteristics of metallic materials, and may be useful in quality control and selection of materials.

Rockwell hardness tests are considered satisfactory for acceptance testing of commercial shipments, and have been used extensively in industry for this purpose.

Rockwell hardness testing at a specific location on a part may not represent the physical characteristics of the whole part or end product.

Adherence to this standard test method provides traceability to national Rockwell hardness standards except as stated otherwise.

1. Scope

1.1 These test methods cover the determination of the Rockwell hardness and the Rockwell superficial hardness of metallic materials by the Rockwell indentation hardness principle. This standard provides the requirements for Rockwell hardness machines and the procedures for performing Rockwell hardness tests.

1.2 This standard includes additional requirements in annexes:

1.3 This standard includes nonmandatory information in appendixes which relates to the Rockwell hardness test.

1.4 Units ā€” At the time the Rockwell hardness test was developed, the force levels were specified in units of kilograms-force (kgf) and the indenter ball diameters were specified in units of inches (in.). This standard specifies the units of force and length in the International System of Units (SI); that is, force in Newtons (N) and length in millimeters (mm). However, because of the historical precedent and continued common usage, force values in kgf units and ball diameters in inch units are provided for information and much of the discussion in this standard refers to these units.

1.5 The test principles, testing procedures, and verification procedures are essentially identical for both the Rockwell and Rockwell superficial hardness tests. The significant differences between the two tests are that the test forces are smaller for the Rockwell superficial test than for the Rockwell test. The same type and size indenters may be used for either test, depending on the scale being employed. Accordingly, throughout this standard, the term Rockwell will imply both Rockwell and Rockwell superficial unless stated otherwise.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A370 Test Methods and Definitions for Mechanical Testing of Steel Products A623 Specification for Tin Mill Products, General Requirements A623M Specification for Tin Mill Products, General Requirements [Metric] B19 Specification for Cartridge Brass Sheet, Strip, Plate, Bar, and Disks B36/B36M Specification for Brass Plate, Sheet, Strip, And Rolled Bar B96/B96M Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels B103/B103M Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar B121/B121M Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar B122/B122M Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar B130 Specification for Commercial Bronze Strip for Bullet Jackets B134/B134M Specification for Brass Wire B152/B152M Specification for Copper Sheet, Strip, Plate, and Rolled Bar B370 Specification for Copper Sheet and Strip for Building Construction E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications E92 Test Method for Vickers Hardness of Metallic Materials E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, and Scleroscope Hardness E384 Test Method for Knoop and Vickers Hardness of Materials E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

Society of Automotive Engineers (SAE) Standard

SAEJ417 Hardness Tests and Hardness Number Conversions Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.

American Bearings Manufacturer Association Standard

ABMA10-1989 Metal Balls Available from American Bearing Manufacturers Association (ABMA), 2025 M Street, NW, Suite 800, Washington, DC 20036.

ISO Standards

ISO/IEC17025 General Requirements for the Competence of Testing and Calibration Laboratories

Keywords

hardness; mechanical test; metals; Rockwell; Metal electrical conductors; Calibration–metals/alloys analysis instrumentation; Rockwell hardness; Testing machines; Verification

ICS Code

ICS Number Code 77.040.10 (Mechanical testing of metals)

DOI: 10.1520/E0018-11 ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]

Related products

ASTM-E18
$38.35