ASTM-A599 2012

$35.75

A599/A599M-07(2012) Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet

Published By	Publication Date	Number of Pages
ASTM	2012	3

Guaranteed Safe Checkout

Categories: 77.140.50 - Flat steel products and semi-products, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Table 1 .

TABLE 1 Electrolytic Tin-Coated Sheets Coating Weight [Mass]

Note 1 Listed below are the commonly produced coating weights [mass] upon agreement between the producer and the purchaser. Other combinations of coatings may be specified and the appropriate minimum average test values ^A apply.

^A Refer to Specifications A623 and A623M .

^B A base box is defined as a unit of area equivalent to 112 sheets 14 in. by 20 in. or 31?360 in. ² (refer to Specification A623 ).

^C The minimum single spot value shall not be less than 80?% of the minimum average tin coating weight [mass] (see 8.1 and 8.2 ).

1.1.1 Electrolytic tin-coated sheet is customarily available as commercial steel (CS); drawing steel (DS); deep drawing steel (DDS); extra deep drawing steel (EDDS), and structural steel (SS). The tin coating is available as unmelted or melted.

1.2 Limitations This specification is applicable to orders in either inch-pound units (as A599), which is supplied in thicknesses from 0.015 in. to 0.036 in., or SI units [as A599M], which is supplied in thicknesses from 0.381 mm to 0.914 mm. For thicknesses lighter than 0.015 in. [0.381 mm], refer to A624/A624M [A624M].

1.3 Unless the order shows the M designation [SI units], the product shall be furnished to inch-pound units. The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.

Additional information

10 (1.1/1.1)	0.05/0.05 (1.1/1.1)
Designation No.	Nominal Tin Coating Weight [Mass] (Each Surface) lb/base box (g/m 2 ) B
5 (0.6/0.6)	0.025/0.025 (0.6/0.6)
50 (5.6/5.6)	0.25/0.25 (5.6/5.6)
15 (1.7/1.7)	0.075/0.075 (1.7/1.7)
25 (2.8/2.8)	0.125/0.125 (2.8/2.8)
100 (11.2/11.2)	0.50/0.50 (11.2/11.2)
75 (8.4/8.4)	0.375/0.375 (8.4/8.4)
20 (2.2/2.2)	0.10/0.10 (2.2/2.2)
ICS Codes	77.140.50 - Flat steel products and semi-products

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-A599 2012

Related products